Napalm OG was bred by Alien Genetics by crossing their Tahoe Alien and Alien Kush strains. As the name indicates, this is a powerful strain that will take down even the most experienced smokers. Expect a spicy, peppery, and lemon kushy aroma and flavor that will leave your senses stimulated and your body sinking into a deep, euphoric stone.
About the strain Napalm OG
In this cartridge, you’ll find Napalm OG, an aromatic and flavorful strain known for its spicy and peppery aroma. It is certain to provide you with an unforgettable smoking experience regardless of whether you are an experienced smoker or just starting out.
The Different Parts of Big Chief THC Cartridge
A THC cartridge is made up of several parts: the cartridge itself, the coil, the wick, and the mouthpiece. The cartridge is the primary element of the gadget and holds the cannabis oil. The coil is covered around the wick and heats up to vaporize the oil. The wick soaks the oil and conveys it to the ring. The mouthpiece is bound to the lid of the cartridge and permits you to pull in the vapor.
The coil is a little metal wire that is encased near the wick. It serves as a heating element and vaporizes the cannabis oil when it gets hot enough. The ring must be made of a substance that can resist elevated temperatures without boiling or softening. Some typical materials used for coils are kanthal, nichrome, and stainless steel.
The wick is a small piece of material that absorbs cannabis oil and transfers it to the coil. It is usually made from cotton, but other materials, such as silica rope or ceramic, can also be used. Wicks need to be replaced periodically because they will eventually get clogged with residue from vaporized oils.
The mouthpiece is bound to the lid of the cartridge and lets you pull in the vapor. It can be made from different materials such as plastic, metal, or glass, but most mouthpieces are made from plastic because it is less likely to break than other materials.
How to Assemble Your Big Chief THC Cartridge
The first step in assembling your THC cartridge is preparing it. You’ll need to remove the cartridge’s top so you can access the coil and wick. To do this, simply unscrew the top of the cartridge from the base. As you’ve done this, you can set aside the top of the cartridge.
Step Two: Assembling the Coil
The next stage is to complete the coil. You’ll need to thread the wire through the holes in the coil to form a tight spiral. Once you’ve done this, you can screw the coil into place at the bottom of the cartridge.
Step Three: Assembling the Wick
The next step is to assemble the wick. You’ll need to thread one end of the wick through the hole in the coil and then screw it into place at
the bottom of the cartridge.
Step Four: Assembling the Mouthpiece
The last step is to make the mouthpiece. You’ll need to tighten the mouthpiece into a spot at the top of the cartridge. Once you’ve done this, your THC cartridge is ready to use!
How to Fill Your Big Chief THC Cartridge
Before you begin filling your THC cartridge, it is vital to first prepare the cartridge itself. This stage is critical in assuring that your cartridge will operate correctly and deliver good-quality vapor.
To prepare the cartridge:
- Start by removing the cap and mouthpiece.
- Use a cotton swab or similar device to cleanse out the interior of the cartridge.
- Empty any mud or rubbish that may be present.
- Once the cartridge is clean, replace the cap and mouthpiece.
Step Two: Filling the Cartridge
Now that the cartridge is prepared, you can begin filling it with THC oil. Start by removing the cap and mouthpiece from the cartridge again. Using a syringe or other similar tool, carefully fill the cartridge with THC oil until it is nearly complete. Be careful not to overfill the cartridge, as this can lead to later problems with the vapor production. Once the cartridge is filled, replace the cap and mouthpiece.
Step Three: Assembling the Coil
The next step in filling your THC cartridge is to assemble the coil. This part of the process is simple; simply screw the coil into place on top of the wick. Make sure that it is screwed in tight so that there are no cracks between the coil and the wick.
Step Four: Assembling the wick.
After assembling The Coil, The next step Is To assemble The Wick. To do this, Simply thread The Wick through The Coil. Make sure that The Wick Is snug against The Coil so That There Is no gap between Them.
Step Five: Assembling the mouthpiece.
The final step In assembling your THC Cartridge Is To attach The Mouthpiece. Screw The Mouthpiece Into place on top of The Cartridge. Make sure That It Is screwed on Tightly So That There Are no gaps between Them.
How to Use Your Big Chief THC Cartridge
To use your THC cartridge, extract the mouthpiece and unscrew the metal lid of the cartridge. Next, screw the cartridge into your vape pen or e-cigarette. Once it is screwed in, press the button on your vape pen or e-cigarette to heat up the coil. Inhale slowly and steadily for about 3-5 seconds. You can then release the button and take a break for a few seconds before taking another hit.
Step Two: Using the Coil
The coil heats up and vaporizes the THC oil inside the cartridge. It is important not to let the coil get too hot, as this can cause it to burn out prematurely. To prevent this, only press the button on your vape pen or e-cigarette for a few seconds at a time when taking a hit. If you notice that the impacts are becoming weaker or less flavorful, it is probably time to replace the coil.
Step Three: Using the Wick
The wick is what absorbs the THC oil and delivers it to the coil to be vaporized. If you notice that your hits are becoming weaker or less flavorful, it is probably because the wick needs to be replaced. To do this, simply remove the old wick and insert a new one into the cartridge.
Using The Mouthpiece
The mouthpiece is where you inhale when taking a hit from your THC cartridge. Some cartridges have removable mouthpieces, while others have permanent ones attached. If yours is removable, take it off when you’re finished using it and put it back on when you’re ready to start again. If it’s not removable, then just make sure to clean it off after each use.